AHA154X.ADD: Difference between revisions

Revision as of 15:21, 1 September 2019

Adapter Device Driver for Adaptec AHA-1540/1542 SCSI host bus adapters and AHA-1740/1742/1744 adapters (in standard mode).

BASEDEV=AHA154X.ADD <parameter>

Parameters

/V : Load driver verbosely. This parameter will display the driver name as well as the version number and Adaptec copyright if the driver loads successfully.
/DBUFF : Loose access to RAM above 16M.
/A:0

/BOFF:t - allows the bus-off time to be set to a value between 1 and 64 microseconds. The default value for OS/2 2.x is 4 microseconds and this should be used for most systems.

/BON:t - allows the bus-on time to be set to a value between 2 and 15 microseconds. The default value for OS/2 2.x is 7 microseconds and this should be used for most systems.

/D - Allow targets to disconnect from the SCSI bus (DEFAULT).
/!D - Prevent targets from disconnecting from the SCSI bus. *** This command is not supported on boards earlier than revision B.

/UR - Report underruns.
/!UR - Ignore underruns (DEFAULT).

TIP: By Prof. C.W. Fischer (Physics Department Director, CPES Micro-Computer Lab). Users may be interested in a undocumented parameter on the Adaptec AHA154x.add file i.e /DBUFF. Anyone using this SCSI adapter without /DBUFF will loose access to RAM above 16M. It's a bus mastering problem on ISA (thanks to Steven Levine).

NOTE: When you use Seagate Backup Exec for OS/2 Warp, Version 3.0 with both a hard drive and a SCSI or QIC backup device connected you have to add - to avoid DMA errors - the following to your driver line to prevent BUS errors: /V /A:0 /BON /A:0 /BOFF:8

Product Support
OS/2 1.3
OS/2 2.0	S
OS/2 2.1	S
OS/2 2.11 SMP	S
OS/2 Warp 3	S
OS/2 Warp Connect	S
OS/2 Warp 4	S
OS/2 Warp Server for e-Business	S

@@ Line 3: / Line 3: @@
 ===Parameters===
-*/V
+*/V : Load driver verbosely. This parameter will display the driver name as well as the version number and Adaptec copyright if the driver loads successfully.
-*/DBUFF - Loose access to RAM above 16M.
+*/DBUFF : Loose access to RAM above 16M.
 */A:0
-*/BON
-*/BOFF:8
+* /BOFF:t - allows the bus-off time to be set to a value between 1 and 64 microseconds. The default value for OS/2 2.x is 4 microseconds and this should be used for most systems.
+* /BON:t - allows the bus-on time to be set to a value between 2 and 15 microseconds. The default value for OS/2 2.x is 7 microseconds and this should be used for most systems.
+* /D - Allow targets to disconnect from the SCSI bus (DEFAULT).
+* /!D - Prevent targets from disconnecting from the SCSI bus. *** This command is not supported on boards earlier than revision B.
+* /UR - Report underruns.
+* /!UR - Ignore underruns (DEFAULT).
 ;TIP:By Prof. C.W. Fischer (Physics Department Director, CPES Micro-Computer Lab). Users may be interested in a undocumented parameter on the Adaptec AHA154x.add file i.e /DBUFF. Anyone using this SCSI adapter without /DBUFF will loose access to RAM above 16M. It's a bus mastering problem on ISA (thanks to Steven Levine).
 ;NOTE: When you use Seagate Backup Exec for OS/2 Warp, Version 3.0 with both a hard drive and a SCSI or QIC backup device connected you have to add - to avoid DMA errors - the following to your driver line to prevent BUS errors: /V /A:0 /BON /A:0 /BOFF:8