IBMIDECD.FLT: Difference between revisions

Revision as of 14:37, 2 March 2018

This filter driver makes your IDE CD-ROM drive visible to OS/2. Support for ATAPI CD-ROM drives attached to an IDE Port. Superseded by IBMATAPI.FLT Version 10.085.

Version

Date	Version	Size	Comments
1998-04-20 20:58	9.23	24,080 bytes
	10.047		IDE CD-RW support
2002-10-08 17:26	10.085	39,416 bytes	Extended Warm Swap Support
2003-01-17 14:52	10.095	24,652 bytes

CONFIG.SYS Information

This filter driver makes IDE CD-ROM drives visible to OS/2. Support for ATAPI CD-ROM drives attached to an IDE Port. Superseded by IBMATAPI.FLT V 10.085. It is important to use IBMIDECD.FLT with the IBM1S506.ADD driver. Since Ver. 10.047 IDE CD-Writers for reading/writing are supported. Note: To get CD-ROM support in OS/2 you must also install IBM1S506.ADD and OS2CDROM.DMD.

BASEDEV=IBMIDECD.FLT <parameter>

Parameters

/V: Displays some information during the boot.
/C: IBMATAPI.FLT and IBMIDECD.FLT have been modified so that they no longer fill the request's S/G list with 0's for the commands without data transfer phase, even if the particular command contains a valid S/G list. To avoid possible unforeseen compatibility problems with older drivers, /C parameter disables this new behaviour.

Platform Support:

OS/2 2.x	OS/2 3.0	OS/2 4.0	OS/2 4.5x
?	Yes	Yes	Yes

@@ Line 1: / Line 1: @@
-This filter driver makes your IDE CD-ROM drive visible to OS/2. Support for ATAPI CD-ROM drives attached to an IDE Port. Superceded by [[IBMATAPI.FLT]] Version 10.085.
+This filter driver makes your IDE CD-ROM drive visible to OS/2. Support for ATAPI CD-ROM drives attached to an IDE Port. Superseded by [[IBMATAPI.FLT]] Version 10.085.
 ==Version==
@@ Line 15: / Line 15: @@
 ==CONFIG.SYS Information==
-This filter driver makes IDE CD-ROM drives visible to OS/2. Support for ATAPI CD-ROM drives attached to an IDE Port. Superceded by IBMATAPI.FLT V 10.085. It is important to use IBMIDECD.FLT with the IBM1S506.ADD driver. Since Ver. 10.047 IDE CD-Writers for reading/writing are supported.
+This filter driver makes IDE CD-ROM drives visible to OS/2. Support for ATAPI CD-ROM drives attached to an IDE Port. Superseded by IBMATAPI.FLT V 10.085. It is important to use IBMIDECD.FLT with the IBM1S506.ADD driver. Since Ver. 10.047 IDE CD-Writers for reading/writing are supported.
-'''Note:''' To get CDRom support in OS/2 you must also install IBM1S506.ADD and Os2cdrom.dmd .
+'''Note:''' To get CD-ROM support in OS/2 you must also install IBM1S506.ADD and OS2CDROM.DMD.
   BASEDEV=IBMIDECD.FLT <parameter>
-'''Parameters:'''
+===Parameters===
+;/V:Displays some information during the boot.
-* /V
+;/C:IBMATAPI.FLT and IBMIDECD.FLT have been modified so that they no longer fill the request's S/G list with 0's for the commands without data transfer phase, even if the particular command contains a valid S/G list. To avoid possible unforeseen compatibility problems with older drivers, /C parameter disables this new behaviour.
-Displays some information during the boot.
-* /C
-IBMATAPI.FLT and IBMIDECD.FLT have been modified so that they no longer fill the request's S/G list with 0's for the commands without data tranfer phase, even if the particular command contains a valid S/G list. To avoid possible unforseen compatibility problems with older drivers, /C parameter disables this new behavior.
 Platform Support:
@@ Line 35: / Line 31: @@
 !OS/2 4.5x
 |-
-|Yes
+|?
 |Yes
 |Yes