IBMATAPI.FLT: Difference between revisions
Created page with "Previously IDE CD-ROM (also CD-R, CD-RW, DVD) devices weres handled by IBMIDECD.FLT and all other ATAPI devices (LS-120, ZIP etc.) by IBMATAPI.FLT. Now all ATAPI devices a..." |
No edit summary |
||
Line 12: | Line 12: | ||
|} | |} | ||
[[Category:Filter Device Drivers]] | ==CONFIG.SYS== | ||
Filter driver ATAPI disks. New with Fixpaks since Fixpak 6/35 supports ATAPI Removable Media like ZIP100 and ZIP250, LS120 attached to an IDE Port. Since build 10.085 IBMATAPI.FLT is a superset of IBMIDECD.FLT. So make sure IBMIDECD.FLT is not in your config.sys. | |||
'''TIP:''' If you have removable media drives (MO, IOMEGA, SYQUEST and others) look at http://rheooptik.fmf.uni-freiburg.de/www/faq/ remmedia.htm for a detailed removable media FAQ. | |||
BASEDEV=Ibmatapi.flt | |||
'''PARAMETER (since 10.085)''' | |||
* /V | |||
Verbose Mode, displays filter status on detected and emulated | |||
devices. | |||
* /A:n | |||
Specify adapter: 0 = primary, 1 = secondary, 2 = DockingStation | |||
primary, 3 = DockingStation secondary. | |||
* /I | |||
Ignore adapter n specified by /A:n. Example: | |||
"/A:1 /I" secondary IDE channel will not be filtered. | |||
* /U:n | |||
Specify unit: 0=master, 1=slave. | |||
* /!U:n | |||
Specified unit will be ignored. Examples: | |||
"/A:1 /!U:1" ignore(not claim) slave unit on secondary IDE channel. | |||
"/A:2 /!U:0" ignore(not claim) DockingStation UltraBay. | |||
* /SCSI | |||
Export IDE device as SCSI device. Can be used to emulate SCSI | |||
CD-RW device as IDE CD-RW device. Example: | |||
"/A:1 /U:0 /SCSI" will report SCSI CD device attached as | |||
secondary IDE channel master unit . | |||
* /TYPES:xxx | |||
Specify device types supported by WarmSwap. x can be C=CD | |||
(CD-ROM,CD-R, CD-RW, DVD, etc), L=LS (LS-120, LS-240), Z=ZIP. | |||
Examples: | |||
"/A:1 /U:0 /TYPES:CLZ" enable swapping between CD, LS and ZIP | |||
"/A:1 /U:0 /TYPES:CZ" enable swapping only between CD and ZIP | |||
If certain device is in the UltraBay during Boot it will be | |||
enabled for swapping. | |||
/C IBMATAPI.FLT has been modified so that it no longer fills the | |||
request's S/G list with 0's for the commands without data | |||
transfer phase, even if the particular command contains a valid | |||
S/G list. To avoid possible unforeseen compatibility problems | |||
with older drivers, /C parameter disables this new behavior. | |||
{| class="wikitable" | |||
|+Platform Support: | |||
!OS/2 2.x | |||
!OS/2 3.0 | |||
!OS/2 4.0 | |||
!OS/2 4.5x | |||
|- | |||
|Yes | |||
|Yes | |||
|Yes | |||
|Yes | |||
|} | |||
[[Category:BASEDEV Statements]][[Category:Filter Device Drivers]] |
Revision as of 22:05, 13 October 2016
Previously IDE CD-ROM (also CD-R, CD-RW, DVD) devices weres handled by IBMIDECD.FLT and all other ATAPI devices (LS-120, ZIP etc.) by IBMATAPI.FLT. Now all ATAPI devices are handled by single this driver.
Version
Date | Version | Size | Comments |
---|---|---|---|
1998-04-20 20:58 | 9.23 | ||
2002-10-08 17:26 | 10.085 | 39,416 bytes | Extended Warm Swap Support |
2003-01-17 14:52 | 10.095 |
CONFIG.SYS
Filter driver ATAPI disks. New with Fixpaks since Fixpak 6/35 supports ATAPI Removable Media like ZIP100 and ZIP250, LS120 attached to an IDE Port. Since build 10.085 IBMATAPI.FLT is a superset of IBMIDECD.FLT. So make sure IBMIDECD.FLT is not in your config.sys.
TIP: If you have removable media drives (MO, IOMEGA, SYQUEST and others) look at http://rheooptik.fmf.uni-freiburg.de/www/faq/ remmedia.htm for a detailed removable media FAQ.
BASEDEV=Ibmatapi.flt
PARAMETER (since 10.085)
- /V
Verbose Mode, displays filter status on detected and emulated devices.
- /A:n
Specify adapter: 0 = primary, 1 = secondary, 2 = DockingStation primary, 3 = DockingStation secondary.
- /I
Ignore adapter n specified by /A:n. Example: "/A:1 /I" secondary IDE channel will not be filtered.
- /U:n
Specify unit: 0=master, 1=slave.
- /!U:n
Specified unit will be ignored. Examples: "/A:1 /!U:1" ignore(not claim) slave unit on secondary IDE channel. "/A:2 /!U:0" ignore(not claim) DockingStation UltraBay.
- /SCSI
Export IDE device as SCSI device. Can be used to emulate SCSI CD-RW device as IDE CD-RW device. Example: "/A:1 /U:0 /SCSI" will report SCSI CD device attached as secondary IDE channel master unit .
- /TYPES:xxx
Specify device types supported by WarmSwap. x can be C=CD (CD-ROM,CD-R, CD-RW, DVD, etc), L=LS (LS-120, LS-240), Z=ZIP. Examples: "/A:1 /U:0 /TYPES:CLZ" enable swapping between CD, LS and ZIP "/A:1 /U:0 /TYPES:CZ" enable swapping only between CD and ZIP If certain device is in the UltraBay during Boot it will be enabled for swapping. /C IBMATAPI.FLT has been modified so that it no longer fills the request's S/G list with 0's for the commands without data transfer phase, even if the particular command contains a valid S/G list. To avoid possible unforeseen compatibility problems with older drivers, /C parameter disables this new behavior.
OS/2 2.x | OS/2 3.0 | OS/2 4.0 | OS/2 4.5x |
---|---|---|---|
Yes | Yes | Yes | Yes |