View source for CONFIG.SYS - DEVICE Statements - ISDN Support

==AVM==
===AVMB1.SYS===
Driver for the AVM active ISDN controller B1.
 DEVICE=AVMB1.SYS

'''Parameter:'''
* /$ - If old programs needs the old naming convention (like an outdated CFOS).

;NOTE:The passive AVM cards (like the FritzCard) aren't supported by AVM with OS/2 Drivers.

===ISDNBASE.SYS===
AVM Fritz ISDN PCCard (aka PCMCIA) driver.
 DEVICE=ISDNBASE.SYS <parameter>

'''Parameter:'''
* /S - Load Silent, no messages during Boot.
* /IRQ:xx - Specifies an Interrupt for the driver, e.g. /IRQ:10
* /IO:xxx - Specifies an IO-Address, whereby possible resources are 140 and 300
* /EXCL:xxxx - a bit mask definition of excluded interrupts, e.g. /excl:F947

==ELSA==
===DSS1C20X.SYS===
CAPI version 2.0 driver for ELSA ISDN board.
* D channel protocol: DSS1 (EURO-ISDN)
* B channel protocols: HDLC transparent, bit transparent, X.75, T.70NL, V.120 ISO 8208 (X.25), T.90 modem function (V.34), Fax group 3 function (V.34 only for PCFpro, QuickStep 3000 and QuickStep 3000-PCI). FAX only for PCF, PCFpro, QuickStep 3000 and QuickStep 3000-PCI.
 DEVICE=DSS1C20X.SYS

'''Parameter:'''
* /a - IO-Port, e.g. /a160
* /r - IRQ, e.g. /r11

===DSS1CAPX.SYS===
CAPI version 1.1 driver for ELSA ISDN board.
* D channel protocol : DSS1 (EURO-ISDN)
* B channel protocols: HDLC transparent, bit transparent, X.75, T.70NL, V.120 ISO 8208 (X.25), T.90 modem function (V.34), Fax group 3 function (V.34 only for PCFpro, QuickStep 3000 and QuickStep 3000-PCI). FAX only for PCF, PCFpro, QuickStep 3000 and QuickStep 3000-PCI.
 DEVICE=DSS1CAPX.SYS <parameters>

'''Parameter:'''
* /a - IO-Port, e.g. /a160
* /r - IRQ, e.g. /r11
* /N0=MSN0 - /N9=MSN9 - Allocation of MSNs

===ISDNC20X.SYS===
CAPI version 2.0 driver for ELSA ISDN board. 
* D channel protocol : 1TR6 (national ISDN)
* B channel protocols: HDLC transparent, bit transparent, X.75, T.70NL, V.120 ISO 8208 (X.25), T.90 modem function (V.34), Fax group 3 function (V.34 only for PCFpro, QuickStep 3000 and QuickStep 3000-PCI). FAX only for PCF, PCFpro, QuickStep 3000 and QuickStep 3000-PCI.
 DEVICE=ISDNC20X.SYS

'''Parameter:'''
* /a IO-Port, e.g. /a160
* /r IRQ, e.g. /r11

===ISDNCAPX.SYS===
CAPI driver for ELSA MicroLink ISDN/PCC-16.

==Eicon==
===CAPI20.OS2===
Eicon Diehl COMMON-ISDN-API Version 2.0.
 DEVICE=CAPI20.OS2

===DIAPIS.OS2===
Eicon Diehl COMMON-ISDN-API Version 1.1.
 DEVICE=DIAPIS.OS2

===DIDD.OS2===
This device driver stores the configuration information of every installed Eicon.Diehl ISDN adapter using the DI(Direct)-Interface and has to be installed before any ISDNSDI.OS2 or ISDNPDI.OS2 drivers.
 DEVICE=DIDD.OS2

===DIMAINT.OS2===
This device driver is a trace interface for all installed Eicon Diel ISDN adapters and is used by the DILOG.EXE application. The content of a DILOG trace depends on the driver which writes information into the DIMAINT buffer. DIMAINT uses no parameter.
 DEVICE=DIMAINT.OS2

===DIVAPP.OS2===
This utility represents the Plug and Play (PnP) enabler for the Eicon Diehl ISA Plug and Play ISDN adapters.
 DEVICE=DIVAPP.OS2 <parameters>

;Parameter:
* -a - I/O address for adapter
* -i - Interrupt number to use
* -q - Quiet mode
* -v - Verbose mode, print detailed information onto screen.

===TED1TR6.OS2===
The TED.OS2 loads the Eicon Diehl ISDN protocol specified by the name "Protocol" and installs the IDI interface.
 DEVICE=TED1TR6.OS2

===TED5ESS.OS2===
The TED.OS2 loads the Eicon Diehl ISDN protocol specified by the name "Protocol" and installs the IDI interface.
 DEVICE=TED5ESS.OS2

===TEDATEL.OS2===
The TED.OS2 loads the Eicon Diehl ISDN protocol specified by the name "Protocol" and installs the IDI interface.
 DEVICE=TEDATEL.OS2

===TEDBELG.OS2===
The TED.OS2 loads the Eicon Diehl ISDN protocol specified by the name "Protocol" and installs the IDI interface.
 DEVICE=TEDBELG.OS2

===TEDETSI.OS2===
The TED.OS2 loads the Eicon Diehl ISDN protocol specified by the name "Protocol" and installs the IDI interface.
 DEVICE=TEDETSI.OS2

===TEDFRANC.OS2===
The TED.OS2 loads the Eicon Diehl ISDN protocol specified by the name "Protocol" and installs the IDI interface.
 DEVICE=TEDFRANC.OS2

===TEDJAPAN.OS2===
The TED.OS2 loads the Eicon Diehl ISDN protocol specified by the name "Protocol" and installs the IDI interface.
 DEVICE=TEDJAPAN.OS2

===TEDNI.OS2===
The TED.OS2 loads the Eicon Diehl ISDN protocol specified by the name "Protocol" and installs the IDI interface.
 DEVICE=TEDNI.OS2

===TEDSWED.OS2===
The TED.OS2 loads the Eicon Diehl ISDN protocol specified by the name "Protocol" and installs the IDI interface.
 DEVICE=TEDSWED.OS2

==HST==
===CAPIVDEV.SYS===
Virtual Device Driver (VDD)32 bit for HST Janus ISDN Cards for DOS.
 DEVICE=CAPIVDEV.SYS

===CCAXI.SYS===
Device driver for HST Janus Saphire ISDN Cards and CAPI v.1.1/2.0 for 1TR6(German) protocol.
 DEVICE=CCAXI.SYS

===CCAXE.SYS===
Device driver for HST Janus Saphire ISDN Cards and CAPI v.1.1/2.0 for DSS-1 (ETSI) protocol.
 DEVICE=CCAXE.SYS

===SCAX.SYS===
Device driver for HST Janus ISDN ISA-Cards and CAPI v.1.1/2.0 for 1TR6 (German) protocol.
 DEVICE=SCAX.SYS

===SCAXE.SYS===
Device driver for HST Janus ISDN ISA-Cards and CAPI v.1.1/2.0 for DSS-1 (ETSI) protocol.
 DEVICE=SCAXE.SYS

==IBM==
===BIPMAC.OS2===
This is a driver for the IBM Active 2000 ISDN card.
 DEVICE=x:\IBMbip\OS2\BIPMAC.OS2 

===BIPPDD.OS2===
This is a driver for the IBM Active 2000 ISDN card.
 DEVICE=x:\IBMbip\OS2\BIPPDD.OS2 <parameter> 

==Teles==
===BUNDLE.SYS===
Module for Teles ISDN Cards.
 DEVICE=BUNDLE.SYS

===CAPI.DLL===
CAPI-DLL v.1.1 16-bit for ISDN Cards.
 DEVICE=CAPI.DLL

===CAPI20.DLL===
CAPI-DLL v.2.0 32-bit for ISDN Cards.
 DEVICE=CAPI20.DLL

===DSS1TE.SYS===
Euro ISDN Module for Teles ISDN Cards
 DEVICE=DSS1TE.SYS
;TIP: If you not already have one better get one from ELSA. Newer Teles Cards are reported to produce many problems (if not fail in general) and there is definitely no further OS/2 development. Also newer Driver Versions (> 2.97) are reported to make trouble.

===HDLC.SYS===
HDLC Module for Teles ISDN Cards.
 DEVICE=HDLC.SYS

===ISDNAPI.SYS===
Module for Teles ISDN Cards.
 DEVICE=ISDNAPI.SYS

===S0TE.SYS===
Module for Teles ISDN-Cards.
 DEVICE=S0TE.SYS

===SOAB.SYS===
Module for Teles ISDN Cards.
 DEVICE=SOAB.SYS

==Misc==
===CFOS.SYS===
CFOS is a driver that sits between your ISDN hardware and your Modem Software (Internet Dialer, Terminal program). It emulates a COM port. 'cFos' device driver receives the usual modem commands, the so-called AT commands from the communication programs and turns them into the corresponding ISDN CAPI commands. ISDN CAPI responses are turned into modem responses of the same meaning, so that the communication programs 'understand' them.
 DEVICE=C:\Cfos\Cfos.Sys <parameters>
As you can enter any equipment names (e.g.: ISDN1) or several COM ports (a maximum of two in the shareware version, up to 30 in 'cFos Professional'). Be careful not to enter COM ports that actually exist as hardware and are in use (e.g. a COM port for your mouse).

;NOTE: The CFOS.SYS driver should be loaded after drivers for serial interfaces (COM.SYS oder SIO.SYS) and after the CAPI driver.

===CFOS20.SYS===
CAPI 2.0 CFOS device driver, for more details see CFOS.SYS.
 DEVICE=CFOS20.SYS

===KSCOM.SYS===
Kamell ISDN Comport Device Driver (At-Commands with Fax Class 2.0)
 DEVICE=KSCOM.SYS <parameter>

'''Parameter:'''
* /P:COMx - Port (Default COM3)
* /C:x - Controller (Default Controller)
* /S:x - Serialnumber
* /A:x - Activation key
* /K:DIVA - Cardtype (only for Eicon Diehl DIVA Cards Version 5.0.3 or higher)

===MACMYWI.OS2===
ISDNPM Support Driver.
 DEVICE=MACMYWI.OS2

[[Category:The Config.sys Documentation Project]]