Jump to content

CONFIG.SYS - DEVICE Statements - ISDN Support

From EDM2
(Redirected from ISDNCAPX.SYS)

AVM

AVMB1.SYS

Driver for the AVM active ISDN controller B1. 

DEVICE=AVMB1.SYS

Parameter:

  • /$ - If old programs needs the old naming convention (like an outdated CFOS).
NOTE
The passive AVM cards (like the FritzCard) aren't supported by AVM with OS/2 Drivers.

ISDNBASE.SYS

AVM Fritz ISDN PCCard (aka PCMCIA) driver. 

DEVICE=ISDNBASE.SYS <parameter>

Parameter:

  • /S - Load Silent, no messages during Boot.
  • /IRQ:xx - Specifies an Interrupt for the driver, e.g. /IRQ:10
  • /IO:xxx - Specifies an IO-Address, whereby possible resources are 140 and 300
  • /EXCL:xxxx - a bit mask definition of excluded interrupts, e.g. /excl:F947

ELSA

DSS1C20X.SYS

CAPI version 2.0 driver for ELSA ISDN board.

  • D channel protocol: DSS1 (EURO-ISDN)
  • B channel protocols: HDLC transparent, bit transparent, X.75, T.70NL, V.120 ISO 8208 (X.25), T.90 modem function (V.34), Fax group 3 function (V.34 only for PCFpro, QuickStep 3000 and QuickStep 3000-PCI). FAX only for PCF, PCFpro, QuickStep 3000 and QuickStep 3000-PCI.
DEVICE=DSS1C20X.SYS

Parameter:

  • /a - IO-Port, e.g. /a160
  • /r - IRQ, e.g. /r11

DSS1CAPX.SYS

CAPI version 1.1 driver for ELSA ISDN board.

  • D channel protocol : DSS1 (EURO-ISDN)
  • B channel protocols: HDLC transparent, bit transparent, X.75, T.70NL, V.120 ISO 8208 (X.25), T.90 modem function (V.34), Fax group 3 function (V.34 only for PCFpro, QuickStep 3000 and QuickStep 3000-PCI). FAX only for PCF, PCFpro, QuickStep 3000 and QuickStep 3000-PCI.
DEVICE=DSS1CAPX.SYS <parameters>

Parameter:

  • /a - IO-Port, e.g. /a160
  • /r - IRQ, e.g. /r11
  • /N0=MSN0 - /N9=MSN9 - Allocation of MSNs

ISDNC20X.SYS

CAPI version 2.0 driver for ELSA ISDN board.

  • D channel protocol : 1TR6 (national ISDN)
  • B channel protocols: HDLC transparent, bit transparent, X.75, T.70NL, V.120 ISO 8208 (X.25), T.90 modem function (V.34), Fax group 3 function (V.34 only for PCFpro, QuickStep 3000 and QuickStep 3000-PCI). FAX only for PCF, PCFpro, QuickStep 3000 and QuickStep 3000-PCI.
DEVICE=ISDNC20X.SYS

Parameter:

  • /a IO-Port, e.g. /a160
  • /r IRQ, e.g. /r11

ISDNCAPX.SYS

CAPI driver for ELSA MicroLink ISDN/PCC-16.

Eicon

CAPI20.OS2

Eicon Diehl COMMON-ISDN-API Version 2.0. 

DEVICE=CAPI20.OS2

DIAPIS.OS2

Eicon Diehl COMMON-ISDN-API Version 1.1. 

DEVICE=DIAPIS.OS2

DIDD.OS2

This device driver stores the configuration information of every installed Eicon.Diehl ISDN adapter using the DI(Direct)-Interface and has to be installed before any ISDNSDI.OS2 or ISDNPDI.OS2 drivers. 

DEVICE=DIDD.OS2

DIMAINT.OS2

This device driver is a trace interface for all installed Eicon Diel ISDN adapters and is used by the DILOG.EXE application. The content of a DILOG trace depends on the driver which writes information into the DIMAINT buffer. DIMAINT uses no parameter. 

DEVICE=DIMAINT.OS2

DIVAPP.OS2

This utility represents the Plug and Play (PnP) enabler for the Eicon Diehl ISA Plug and Play ISDN adapters. 

DEVICE=DIVAPP.OS2 <parameters>
Parameter
  • -a - I/O address for adapter
  • -i - Interrupt number to use
  • -q - Quiet mode
  • -v - Verbose mode, print detailed information onto screen.

TED1TR6.OS2

The TED.OS2 loads the Eicon Diehl ISDN protocol specified by the name "Protocol" and installs the IDI interface. 

DEVICE=TED1TR6.OS2

TED5ESS.OS2

The TED.OS2 loads the Eicon Diehl ISDN protocol specified by the name "Protocol" and installs the IDI interface. 

DEVICE=TED5ESS.OS2

TEDATEL.OS2

The TED.OS2 loads the Eicon Diehl ISDN protocol specified by the name "Protocol" and installs the IDI interface. 

DEVICE=TEDATEL.OS2

TEDBELG.OS2

The TED.OS2 loads the Eicon Diehl ISDN protocol specified by the name "Protocol" and installs the IDI interface. 

DEVICE=TEDBELG.OS2

TEDETSI.OS2

The TED.OS2 loads the Eicon Diehl ISDN protocol specified by the name "Protocol" and installs the IDI interface. 

DEVICE=TEDETSI.OS2

TEDFRANC.OS2

The TED.OS2 loads the Eicon Diehl ISDN protocol specified by the name "Protocol" and installs the IDI interface. 

DEVICE=TEDFRANC.OS2

TEDJAPAN.OS2

The TED.OS2 loads the Eicon Diehl ISDN protocol specified by the name "Protocol" and installs the IDI interface. 

DEVICE=TEDJAPAN.OS2

TEDNI.OS2

The TED.OS2 loads the Eicon Diehl ISDN protocol specified by the name "Protocol" and installs the IDI interface. 

DEVICE=TEDNI.OS2

TEDSWED.OS2

The TED.OS2 loads the Eicon Diehl ISDN protocol specified by the name "Protocol" and installs the IDI interface. 

DEVICE=TEDSWED.OS2

HST

CAPIVDEV.SYS

Virtual Device Driver (VDD)32 bit for HST Janus ISDN Cards for DOS. 

DEVICE=CAPIVDEV.SYS

CCAXI.SYS

Device driver for HST Janus Saphire ISDN Cards and CAPI v.1.1/2.0 for 1TR6(German) protocol. 

DEVICE=CCAXI.SYS

CCAXE.SYS

Device driver for HST Janus Saphire ISDN Cards and CAPI v.1.1/2.0 for DSS-1 (ETSI) protocol. 

DEVICE=CCAXE.SYS

SCAX.SYS

Device driver for HST Janus ISDN ISA-Cards and CAPI v.1.1/2.0 for 1TR6 (German) protocol. 

DEVICE=SCAX.SYS

SCAXE.SYS

Device driver for HST Janus ISDN ISA-Cards and CAPI v.1.1/2.0 for DSS-1 (ETSI) protocol. 

DEVICE=SCAXE.SYS

IBM

BIPMAC.OS2

This is a driver for the IBM Active 2000 ISDN card. 

DEVICE=x:\IBMbip\OS2\BIPMAC.OS2

BIPPDD.OS2

This is a driver for the IBM Active 2000 ISDN card. 

DEVICE=x:\IBMbip\OS2\BIPPDD.OS2 <parameter>

Teles

BUNDLE.SYS

Module for Teles ISDN Cards. 

DEVICE=BUNDLE.SYS

CAPI.DLL

CAPI-DLL v.1.1 16-bit for ISDN Cards. 

DEVICE=CAPI.DLL

CAPI20.DLL

CAPI-DLL v.2.0 32-bit for ISDN Cards. 

DEVICE=CAPI20.DLL

DSS1TE.SYS

Euro ISDN Module for Teles ISDN Cards 

DEVICE=DSS1TE.SYS
TIP
If you not already have one better get one from ELSA. Newer Teles Cards are reported to produce many problems (if not fail in general) and there is definitely no further OS/2 development. Also newer Driver Versions (> 2.97) are reported to make trouble.

HDLC.SYS

HDLC Module for Teles ISDN Cards. 

DEVICE=HDLC.SYS

ISDNAPI.SYS

Module for Teles ISDN Cards. 

DEVICE=ISDNAPI.SYS

S0TE.SYS

Module for Teles ISDN-Cards. 

DEVICE=S0TE.SYS

SOAB.SYS

Module for Teles ISDN Cards. 

DEVICE=SOAB.SYS

Misc

CFOS.SYS

CFOS is a driver that sits between your ISDN hardware and your Modem Software (Internet Dialer, Terminal program). It emulates a COM port. 'cFos' device driver receives the usual modem commands, the so-called AT commands from the communication programs and turns them into the corresponding ISDN CAPI commands. ISDN CAPI responses are turned into modem responses of the same meaning, so that the communication programs 'understand' them. 

DEVICE=C:\Cfos\Cfos.Sys <parameters>

As you can enter any equipment names (e.g.: ISDN1) or several COM ports (a maximum of two in the shareware version, up to 30 in 'cFos Professional'). Be careful not to enter COM ports that actually exist as hardware and are in use (e.g. a COM port for your mouse).

NOTE
The CFOS.SYS driver should be loaded after drivers for serial interfaces (COM.SYS oder SIO.SYS) and after the CAPI driver.

CFOS20.SYS

CAPI 2.0 CFOS device driver, for more details see CFOS.SYS. 

DEVICE=CFOS20.SYS

KSCOM.SYS

Kamell ISDN Comport Device Driver (At-Commands with Fax Class 2.0) 

DEVICE=KSCOM.SYS <parameter>

Parameter:

  • /P:COMx - Port (Default COM3)
  • /C:x - Controller (Default Controller)
  • /S:x - Serialnumber
  • /A:x - Activation key
  • /K:DIVA - Cardtype (only for Eicon Diehl DIVA Cards Version 5.0.3 or higher)

MACMYWI.OS2

ISDNPM Support Driver. 

DEVICE=MACMYWI.OS2
Retrieved from "https://www.edm2.com/index.php?title=CONFIG.SYS_-_DEVICE_Statements_-_ISDN_Support&oldid=76649#ISDNCAPX.SYS"