CONFIG.SYS - DEVICE Statements - ISDN Support

From EDM2
Jump to: navigation, search

AVM

AVMB1.SYS

Driver for the AVM Active ISDN-Controller B1.

DEVICE=AVMB1.SYS

Parameter:

  • /$ - If old programs needs the old naming convention (like an outdated CFOS).

NOTE: The passive AVM-Cards (like the Fritzcard) aren't supported by AVM with OS/2 Drivers.

Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

ISDNBASE.SYS

AVM Fritz ISDN PCCard (aka PCMCIA) driver.

DEVICE=ISDNBASE.SYS <parameter>

Parameter:

  • /S - Load Silent, no messages during Boot.
  • /IRQ:xx - Specifies an Interrupt for the driver, e.g. /IRQ:10
  • /IO:xxx - Specifies an IO-Address, whereby possible resources are 140 and 300
  • /EXCL:xxxx - a bit mask definition of excluded interrupts, eg. /excl:F947
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
No Yes Yes Yes

ELSA

DSS1C20X.SYS

CAPI version 2.0 driver for ELSA ISDN board.

  • D channel protocol : DSS1 (EURO-ISDN)
  • B channel protocols: HDLC transparent, bit transparent, X.75, T.70NL, V.120 ISO 8208 (X.25), T.90 modem function (V.34), Fax group 3 function (V.34 only for PCFpro, QuickStep 3000 and QuickStep 3000-PCI). FAX only for PCF, PCFpro, QuickStep 3000 and QuickStep 3000-PCI.
DEVICE=DSS1C20X.SYS

Parameter:

  • /a - IO-Port, e.g. /a160
  • /r - IRQ, e.g. /r11
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

DSS1CAPX.SYS

CAPI version 1.1 driver for ELSA ISDN board.

  • D channel protocol : DSS1 (EURO-ISDN)
  • B channel protocols: HDLC transparent, bit transparent, X.75, T.70NL, V.120 ISO 8208 (X.25), T.90 modem function (V.34), Fax group 3 function (V.34 only for PCFpro, QuickStep 3000 and QuickStep 3000-PCI). FAX only for PCF, PCFpro, QuickStep 3000 and QuickStep 3000-PCI.
DEVICE=DSS1CAPX.SYS <parameters>

Parameter:

  • /a - IO-Port, e.g. /a160
  • /r - IRQ, e.g. /r11
  • /N0=MSN0 - /N9=MSN9 - Allocation of MSNs
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

ISDNC20X.SYS

CAPI version 2.0 driver for ELSA ISDN board.

  • D channel protocol : 1TR6 (national ISDN)
  • B channel protocols: HDLC transparent, bit transparent, X.75, T.70NL, V.120 ISO 8208 (X.25), T.90 modem function (V.34), Fax group 3 function (V.34 only for PCFpro, QuickStep 3000 and QuickStep 3000-PCI). FAX only for PCF, PCFpro, QuickStep 3000 and QuickStep 3000-PCI.
DEVICE=ISDNC20X.SYS

Parameter:

  • /a IO-Port, e.g. /a160
  • /r IRQ, e.g. /r11
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
No Yes Yes Yes

Eicon

CAPI20.OS2

Eicon Diehl COMMON-ISDN-API Version 2.0.

DEVICE=CAPI20.OS2
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

DIAPIS.OS2

Eicon Diehl COMMON-ISDN-API Version 1.1.

DEVICE=DIAPIS.OS2
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

DIDD.OS2

This device driver stores the configuration information of every installed Eicon.Diehl ISDN-Adapter using the DI(Direct)-Interface and has to be installed before any ISDNSDI.OS2 or ISDNPDI.OS2 drivers.

DEVICE=DIDD.OS2
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

DIMAINT.OS2

This device driver is a trace interface for all installed Eicon Diel ISDN adapters and is used by the DILOG.EXE application. The content of a DILOG trace depends on the driver which writes information into the DIMAINT buffer. DIMAINT uses no parameter.

DEVICE=DIMAINT.OS2
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

DIVAPP.OS2

This utility represents the Plug and Play (PnP) enabler for the Eicon Diehl ISA Plug and Play ISDN adapters.

DEVICE=DIVAPP.OS2 <parameters>
Parameter
  • -a

I/O address for adapter

  • -i

Interrupt number to use

  • -q

Quiet mode

  • -v

Verbose mode, print detailed information onto screen.

Platform Support:

OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes


TED1TR6.OS2

The TED.OS2 loads the Eicon Diehl ISDN protocol specified by the name "Protocol" and installs the IDI interface.

DEVICE=TED1TR6.OS2
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

TED5ESS.OS2

The TED.OS2 loads the Eicon Diehl ISDN protocol specified by the name "Protocol" and installs the IDI interface.

DEVICE=TED5ESS.OS2
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

TEDATEL.OS2

The TED.OS2 loads the Eicon Diehl ISDN protocol specified by the name "Protocol" and installs the IDI interface.

DEVICE=TEDATEL.OS2
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

TEDBELG.OS2

The TED.OS2 loads the Eicon Diehl ISDN protocol specified by the name "Protocol" and installs the IDI interface.

DEVICE=TEDBELG.OS2
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

TEDETSI.OS2

The TED.OS2 loads the Eicon Diehl ISDN protocol specified by the name "Protocol" and installs the IDI interface.

DEVICE=TEDETSI.OS2

Platform Support:

Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

TEDFRANC.OS2

The TED.OS2 loads the Eicon Diehl ISDN protocol specified by the name "Protocol" and installs the IDI interface.

DEVICE=TEDFRANC.OS2
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

TEDJAPAN.OS2

The TED.OS2 loads the Eicon Diehl ISDN protocol specified by the name "Protocol" and installs the IDI interface.

DEVICE=TEDJAPAN.OS2

Platform Support:

Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

TEDNI.OS2

The TED.OS2 loads the Eicon Diehl ISDN protocol specified by the name "Protocol" and installs the IDI interface.

DEVICE=TEDNI.OS2
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

TEDSWED.OS2

The TED.OS2 loads the Eicon Diehl ISDN protocol specified by the name "Protocol" and installs the IDI interface.

DEVICE=TEDSWED.OS2
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

HST

CAPIVDEV.SYS

Virtual Device Driver (VDD)32 bit for HST Janus ISDN Cards for DOS.

DEVICE=CAPIVDEV.SYS
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

CCAXI.SYS

Device driver for HST Janus Saphire ISDN Cards and CAPI v.1.1/2.0 for 1TR6(German) protocol.

DEVICE=CCAXI.SYS
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

CCAXE.SYS

Device driver for HST Janus Saphire ISDN Cards and CAPI v.1.1/2.0 for DSS-1 (ETSI) protocol.

DEVICE=CCAXE.SYS
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

SCAX.SYS

Device driver for HST Janus ISDN ISA-Cards and CAPI v.1.1/2.0 for 1TR6 (German) protocol.

DEVICE=SCAX.SYS
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

SCAXE.SYS

Device driver for HST Janus ISDN ISA-Cards and CAPI v.1.1/2.0 for DSS-1 (ETSI) protocol.

DEVICE=SCAXE.SYS
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

IBM

BIPMAC.OS2

This is a driver for the IBM Active 2000 ISDN card.

DEVICE=x:\IBMbip\OS2\BIPMAC.OS2 
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

BIPPDD.OS2

This is a driver for the IBM Active 2000 ISDN card.

DEVICE=x:\IBMbip\OS2\BIPPDD.OS2 <parameter> 
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

Teles

BUNDLE.SYS

Module for Teles ISDN Cards.

DEVICE=BUNDLE.SYS
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

CAPI.DLL

CAPI-DLL v.1.1 16-bit for ISDN Cards.

DEVICE=CAPI.DLL
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

CAPI20.DLL

CAPI-DLL v.2.0 32-bit for ISDN Cards.

DEVICE=CAPI20.DLL
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

DSS1TE.SYS

Euro ISDN Module for Teles ISDN Cards

DEVICE=DSS1TE.SYS

TIP: If you not already have one better get one from ELSA. Newer Teles Cards are reported to produce many problems (if not fail in general) and there is definetly no further OS/2 development. Also newer Driver Versions (> 2.97) are reported to make trouble.

Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

HDLC.SYS

HDLC Module for Teles ISDN Cards.

DEVICE=HDLC.SYS
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

ISDNAPI.SYS

Module for Teles ISDN Cards.

DEVICE=ISDNAPI.SYS
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
No Yes Yes Yes

S0TE.SYS

Module for Teles ISDN-Cards.

DEVICE=S0TE.SYS
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

SOAB.SYS

Module for Teles ISDN Cards.

DEVICE=SOAB.SYS
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

Misc

CFOS.SYS

CFOS is a driver that sits between your ISDN hardware and your Modem Software (Internet Dialer, Terminal program). It emulates a COM port. 'cFos' device driver receives the usual modem commands, the so-called AT commands from the communication programs and turns them into the corresponding ISDN CAPI commands. ISDN CAPI responses are turned into modem responses of the same meaning, so that the communication programs 'understand' them.

DEVICE=C:\Cfos\Cfos.Sys <parameters>

As you can enter any equipment names (e.g.: ISDN1) or several COM ports (a maximum of two in the shareware version, up to 30 in 'cFos Professional'). Be careful not to enter COM ports that actually exist as hardware and are in use (e.g. a COM port for your mouse).

NOTE: The CFOS.SYS driver should be loaded after drivers for serial interfaces (COM.SYS oder SIO.SYS) and after the CAPI driver.

Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

CFOS20.SYS

CAPI 2.0 CFOS device driver, for more details see DEVICE CFOS.SYS.

DEVICE=CFOS20.SYS
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

KSCOM.SYS

Kamell ISDN Comport Device Driver (At-Commands with Fax Class 2.0)

DEVICE=KSCOM.SYS <parameter>

Parameter:

  • /P:COMx - Port (Default COM3)
  • /C:x - Controller (Default Controller)
  • /S:x - Serialnumber
  • /A:x - Activation key
  • /K:DIVA - Cardtype (only for Eicon Diehl DIVA Cards Version 5.0.3 or higher)
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes

MACMYWI.OS2

ISDNPM Support Driver.

DEVICE=MACMYWI.OS2
Platform Support:
OS/2 2.x OS/2 3.0 OS/2 4.0 OS/2 4.5x
Yes Yes Yes Yes